Go back to home

'Will it fit' thread #573

Author
Post
Essentials Only Full Version
D.J
MR2 Enthusiast
  • Total Posts : 153
  • Scores: 2
  • Reward points: 353
  • Joined: 2013/06/04 01:56:15
  • Status: offline
2013/06/27 11:37:09 (permalink)
0

'Will it fit' thread #573

Lowered SW20 Gen II
Planning 17x8 +35's all round (not staggered boo). Will these fit fine or will will I need spacers, guard rolling etc.
 
Thanks.
#1


6 Replies Related Threads
    dylmrt
    Vendor
    • Total Posts : 2156
    • Scores: 111
    • Reward points: 6118
    • Joined: 2011/04/07 19:51:15
    • Location: NSW Australia
    • Status: offline
    Re: 'Will it fit' thread #573 2013/06/27 14:15:58 (permalink)
    0
    on the face of things yes. but each wheel is different so you may still come across issues.

     
    New/used genuine parts for the MR2 community. Send requests through to www.gorillaindustries.com.au/contact
    2002 3SGTE ST246 N-Edition | 1999 3SGTE SW20 GT-S | 1995 3SGTE SW20 GT | 1986 4AGZE AW11 | Join the MR2 Club of NSW http://mr2club.com.au/nsw/
    #2
    Cruiser97_80
    MR2 Enthusiast
    • Total Posts : 118
    • Scores: 0
    • Reward points: 5693
    • Joined: 2011/04/07 19:51:15
    • Location: Tas Australia
    • Status: offline
    Re: 'Will it fit' thread #573 2013/06/27 20:51:03 (permalink)
    0
    Lowered on coil-overs or lowering springs with the std. strut/spring perch?

    1991 SW20 GT
    2007 KUN26 SR5
    2008 GSU45 KX-S
    2008 VDJ200 SAHARA
     
    #3

    Eric
    QLD Moderator
    • Total Posts : 1117
    • Scores: 280
    • Reward points: 4319
    • Joined: 2012/04/06 21:41:57
    • Status: offline
    Re: 'Will it fit' thread #573 2013/06/28 09:11:53 (permalink)
    0
    those will clear fine in the rear, will be about 20mm less than flush though

    as for fronts, they may hit coilovers, so you may require a 2-3mm slip on

    -Eric
    #4
    D.J
    MR2 Enthusiast
    • Total Posts : 153
    • Scores: 2
    • Reward points: 353
    • Joined: 2013/06/04 01:56:15
    • Status: offline
    Re: 'Will it fit' thread #573 2013/07/16 13:10:16 (permalink)
    0
    Ended up with works 17x7.5/8.5 rims.
    Fronts scrub, rears sit pretty flush. Will need new suspension to sort it.
    #5
    dylmrt
    Vendor
    • Total Posts : 2156
    • Scores: 111
    • Reward points: 6118
    • Joined: 2011/04/07 19:51:15
    • Location: NSW Australia
    • Status: offline
    Re: 'Will it fit' thread #573 2013/07/16 15:31:05 (permalink)
    0
    Where's it scrubbing?

     
    New/used genuine parts for the MR2 community. Send requests through to www.gorillaindustries.com.au/contact
    2002 3SGTE ST246 N-Edition | 1999 3SGTE SW20 GT-S | 1995 3SGTE SW20 GT | 1986 4AGZE AW11 | Join the MR2 Club of NSW http://mr2club.com.au/nsw/
    #6

    D.J
    MR2 Enthusiast
    • Total Posts : 153
    • Scores: 2
    • Reward points: 353
    • Joined: 2013/06/04 01:56:15
    • Status: offline
    Re: 'Will it fit' thread #573 2013/07/17 16:23:48 (permalink)
    0
    Not sure, probably on the inside of the guards. Would need flared at that ride height/camber.
    #7
    Jump to:
    © 2025 APG vNext Trial Version 5.5