[QLD]-Totenkopf-'s Universal Performance Parts Clearout

Putting these in a seperate thread so I can add them to other forums easily without having to sift through my other post. 
 
Universal
A) Weldon 2025A Fuel Pump
This fuel pump is the big daddy. It is in 'as new' condition and was barely used. It did two drag meets on a rotary powered altered drag car before being replace with a mechanical fuel pump. I have used pumps such as the Aeromotive A1000 and SX Performance Fuel pumps and always had reliability issues or fuel heating issues (compounded by the flow through design of the aforementioned pumps) so I bought this mac daddy of a pump and was going to run a deadheaded fuel rail to cure such problems. This is a serious bit of kit and will cost in excess of $750 + freight from the USA. Pump is -12AN inlet, -10AN outlet. Below is Weldon's blurg on this pump.

Maximum HP: (-12 inlet and -10 outlet) 1400 hp Inj @ 14V EFI (700 hp on Methanol) & 1600 hp @ 14V Carb (800 hp on Methanol)
GPH/PSI Range: 140-180 GPH / 0-80 PSI
Considerations: If your actual horsepower is close to the Max HP limit and/or you are considering a power adder, See Part # D2035-A or 2345-A
Features:

• Self Priming
  Pump may be mounted above fuel cell
  vertical or horizontal mount
   No plastics or composite materials. Our internal pumping elements are made of high speed tool steel and bronze. This results in the longest lasting, highest quality, most durable pumps available.
• Breakaway coupling prevents pump/motor damage in the event of fuel contamination
• All internal wear components are 100% metallic
• Body machined from billet aluminum
• For carbureted or injected engines
• Provides Consistent Performance with no fall-off in flow
• Precise fuel delivery
• Blades self-compensating for wear
  Current Fluids :
  Weldon Pumps offer the widest range of fuel compatibility.
• Gasoline
• Diesel
• Methanol
• Ethanol
• Nitromethane
• All racing fuels
  Asking $500 with money back satisfaction guarantee.
  
  B) Aeromotive Billet Fuel Pump Speed Controller
  Used for 2000km on my car, was new before this. Been sitting around forever since. Basically replicates the standard dual speed system but using solid state electronics and is designed for a much higher current rating. The switching point for hi/low speed operation is also adjustable.
  VGC
  $200 
   
  C) Takata MPH-341 Harness
  Never been used, still in box. The FIA approval expires this year, however, cams allow use for a further 5 years (soon possibly to be 10). Been sitting in the cupboard for 5 years now. Time for it to go.
  $200 $100
  
  D) Weldon A2040-281-A-120 Fuel Pressure Regulator
  This is the recommended regulator for use with the weldon fuel pump already listed. The weldon fuel pump requires a -8 return line. This regulator has 2x-10 inlet ports and a -8 return port, as well as the usual gauge ports.
  Brand new in box.
  $200
  
  E) Bride Vios III Sport Seat
  Brand new, never left the plastic. Bought this a few years ago with intent to fit to MR2, never happened. Have a set of rails to suit, as listed below in MR2 specific.
  $550 ($700 inc. rails)
  
  F) Aermotive -10 Fuel Filter (100 micron S/S filter fitted)
  Couple of cosmetic blemishes on the outside as this filter has been used. 100 micron is used for pre-pump filtration.
  $50
  
  G) Aeromotive -10 Fuel Filter, replacement element, 10 micron
  Could be used in the above housing, 10 micron for pre injector filtration. Brand new in box.
  $15
  
  H) Aeromotive 12302 #12AN Pro-Series 100 Micron Fuel Filter
  Electroless nickel finish -12 fuel filter. Brand new in Box. 100 micron element for pre-pump use. Was going to be used with the mac daddy weldon pump listed above.
  $120
  
  I) NGK V-Power Racing Spark Plugs
  R5671A-8 (Heat range 8) 2 boxes
  R5671A-9 (Heat Range 9) 2 boxes
  These are non-resistor plugs. I couldn't connect to my Autronic ECU when using these with CDI ignition setup. Not sure how they'd go on a standard car?
  $10 per box of 4
  J) Wilwood Forged Billet Superlite Calipers
  Pair, brand new, never got used. 4 piston, suit 1.25" rotor I am pretty sure.
  $250
  
  K) MSD 8920 Tach Adapter
  Required if you get rid of the standard ignitor (ie, fit a CDI, etc) in order for the tacho to operate. Cant remember specifics, there is the 8920 and 8910 I think, useable in different situations. I know I was running a CDI and required the 8920 unit. Have wired a plug onto it, just your standard weatherpack connector you can get at most auto stores.
  $40  
  L) Volk Racing RE30 Forged Wheels - 17x8 +38, 18x9.5 +42 w/ Falken RT615's
  Mint RE30's, travelled 2000km with these so tyres still have masses of tread left (I bought the wheels and tyres new).  Bronze in colour, 17"->18" front rear stagger.  No gutter rash, grazes or scratches.  Come with hubcentric rings to suit MR2 and also Volk carbon type centre caps.
  Suit new wheel buyer who is looking to save a bit of cash.  Will get further pictures of all the individual rims once it stops pissing down rain outside.  In the meanwhile, here are some of the wheels fitted to the car.  You need to be conscious of front suspension setup with these.  I ran them without any spacers up front but only had a few mm clearance between COILOVERS & the tyre.  Coilovers are pretty much a prerequisite.  Some may fit and some may not.  Recommend trial fit with your particular suspension.  These are basically one of the lightest wheels available on the market.  Tyres are 225 wide up front and 275 wide on the rear.
  $3500 $2900 $2700
  
  A)
  
  B)
  
  C)
  
  D)
  
  E)
  
  
  
  H)
  
  
  I)
   
  J)
  
  
  K)
  
  L)
  
  
  
  

Hey man, someone might be taking it already.  It'll suit anything if you want to use the tach output from an aftermarket ecu into the standard tacho, which I assume is what you'll be after.
 
If the sale falls over I will let you know.
 
Cheers,
 
James.

Still got bits available!

PM sent, few bits still left, happy to entertain some offers.

hi,
 
Part number on the wilwood calipers please?
 
Take Care,
    Haydon 

Sorry, I've fallen off the radar a bit, will pm you.

Seat sold.  ONO for the rest.

Apologies, I have 2 boxes of 8 heat range and 4 boxes of 9 heat range.  New and unused, boxes look a bit tatty, been sitting in the cupboard for probably 4 or 5 years.