Go back to home

3sgte or 3sge torque plate now for hire.

Author
Post
Essentials Only Full Version
92 Hard Top
MR2 Deity
  • Total Posts : 520
  • Scores: 43
  • Reward points: 5815
  • Joined: 2011/04/07 19:51:15
  • Location: Adelaide SA Australia
  • Status: offline
2018/10/16 10:36:09 (permalink)
0

3sgte or 3sge torque plate now for hire.

Does anyone have one, That I can buy or hire?
post edited by 92 Hard Top - 2018/10/23 17:10:42
#1


7 Replies Related Threads
    92 Hard Top
    MR2 Deity
    • Total Posts : 520
    • Scores: 43
    • Reward points: 5815
    • Joined: 2011/04/07 19:51:15
    • Location: Adelaide SA Australia
    • Status: offline
    Re: 3sgte torque plate 2018/10/17 10:59:25 (permalink)
    0
    I can get one made. Would anyone else be interested in it after I used it? You can buy it and sell it after or hire it from me. Can I get some feed back please.
    #2
    Falcon
    Supporter
    • Total Posts : 623
    • Scores: 167
    • Reward points: 5033
    • Joined: 2011/04/07 19:51:15
    • Location: Brisbane Australia
    • Status: offline
    Re: 3sgte torque plate 2018/10/18 09:22:32 (permalink)
    0
    Have you spoken to Rhemac in Gawler. Many years ago I found them to be very good with engine machine work.
    Prepared to bore and hone to my specs to give the clearances I required. Most of those blokes would be dead by now but they may have taught the new generation. They would possibly have a 3S. torque plate.
    #3

    92 Hard Top
    MR2 Deity
    • Total Posts : 520
    • Scores: 43
    • Reward points: 5815
    • Joined: 2011/04/07 19:51:15
    • Location: Adelaide SA Australia
    • Status: offline
    Re: 3sgte torque plate 2018/10/18 10:42:22 (permalink)
    0
    Falcon
    Have you spoken to Rhemac in Gawler. Many years ago I found them to be very good with engine machine work.
    Prepared to bore and hone to my specs to give the clearances I required. Most of those blokes would be dead by now but they may have taught the new generation. They would possibly have a 3S. torque plate.


    Thanks Doug. I will check it out.
    #4
    92 Hard Top
    MR2 Deity
    • Total Posts : 520
    • Scores: 43
    • Reward points: 5815
    • Joined: 2011/04/07 19:51:15
    • Location: Adelaide SA Australia
    • Status: offline
    Re: 3sgte torque plate 2018/10/18 12:02:57 (permalink)
    0
    Rhemac doesn't have one.
    #5
    92 Hard Top
    MR2 Deity
    • Total Posts : 520
    • Scores: 43
    • Reward points: 5815
    • Joined: 2011/04/07 19:51:15
    • Location: Adelaide SA Australia
    • Status: offline
    Re: 3sgte torque plate 2018/10/18 22:47:49 (permalink)
    0

    Finally work out how to install Sard 63507 800cc fuel injectors into Gen II fuel rail which is bore out to 8 to 10mm, have to cut the yellow bit off and add the alloy sleeve, then change o-rings around. Then take the thick o-ring one off the 430cc and put it on the new injectors. All done, happy now. Money Save! Had these sitting in shed for a few years.
    #6

    92 Hard Top
    MR2 Deity
    • Total Posts : 520
    • Scores: 43
    • Reward points: 5815
    • Joined: 2011/04/07 19:51:15
    • Location: Adelaide SA Australia
    • Status: offline
    Re: 3sgte torque plate 2018/10/23 16:53:15 (permalink)
    0
    I have had a 3sgte honing torque plate made. It's for hire $150.00 per job plus shipping and return shipping. These cost $600 in the US. If you want the perfect piston and cylinder seal you need this Honing Torque plate.


    post edited by 92 Hard Top - 2018/11/20 10:24:42
    #7
    92 Hard Top
    MR2 Deity
    • Total Posts : 520
    • Scores: 43
    • Reward points: 5815
    • Joined: 2011/04/07 19:51:15
    • Location: Adelaide SA Australia
    • Status: offline
    Re: 3sgte torque plate 2018/11/20 10:25:30 (permalink)
    0
    "Bump"
    #8
    Jump to:
    © 2025 APG vNext Trial Version 5.5