Brakes

To Bottom

Brakes (p.7)
Post New Thread
Regular
Highlander

Bleeding SW20 Brakes?

Frustrating Day. Have fitted Lexus/rebuilt 300ZXTT caliper front conversion and RX8 Sport on rear with late MR2 calipers. 1" Landcruiser Master cylinder. Master cylinder properly bench bled, brakes beld both with and without motor running. Gives a good hard pedal with acceptable travel when stationa..
8
2013/11/18 21:51:57
mms78

Where to buy replacement pads?

I'm after some rear pads for a SC aw11. My local aussie auto store wanted to charge me $260 for EBC greens, and couldn't locate an alternative. Seemed a bit steep, so I'm asking if anyone knows where I can get a pad suitable for street and light track at an affordable price...
3
2013/11/05 11:38:04
Randomity

Late Model brake troubles?

So here's the story.decided to do the late model brake upgrade. bought the calipers, BMC, rebuild kits, new rotors, etc. Everything I'd need to do it properly.conversion took a bit longer than expected and I finished this morning. rear rotors were delivered as wrong part, so i just left the old ones..
21
2013/10/27 18:24:16
violator

Installing ABS

I'm soon to take possession of a Bathurst (with gen 3 turbo goodness, but without ABS).Has anyone installed ABS?Thanks..
3
2013/10/12 15:32:35
michalcapar

sw20 brake caliper interchangeability between toyota models

Hello guys, New to the mr2 and this forum http://www.mr2.com/forums/images/smilies/wavey.gif I was just wondering if there are any Toyota models that have interchangeable parts with the mr2. The reason im asking is because I've heard that some gens of the toyota 4runner have the same/similar whee..
6
2013/08/26 04:31:06
rico

When to replace your rotors?

Hey guys. When should i be replacing my rotors? If there are no noticeable cracks, what is the minimum thickness until i need them replaced. Ive read somewhere the minimum thickness is engraved into the edge of the rotor. But maybe its not the case with the DBA rotors i have. Keep in mind i have lat..
4
2013/07/31 19:14:34
jason_2901

master cylinder size question

Hey guys I recently bought some gen3 brakes for my 91t, I also got the 15/16 mc with them, just wondering if its worth going to a 1" master or will the 15/16 be ok? By my calculations its only about a 1mm bore difference?..
1
2013/07/12 11:26:26
Randomity

Removing Air from the ABS reservoir?

Hey guys,a while back, I upgraded my suspension from Gen 2 to Gen 3 spring/shock combo, and as you would know, you have to disconnect the brake line from the caliper to do so. The problem being that I then went and got a business (I won't say who) to suck the air out of the lines. They (very cleverl..
1
2013/07/10 21:51:51
bigh

1990 JDM Turbo stock brakes part numbers

Hey everyone. Does anyone have suggestions for new pads and rotors for a 1990 JDM turbo mr2 including part numbers? Looking for best bang for buck. I'm thinking trw pads and rda disks. I want disks that won't warp easily. The disks I had on the car originally warped, then the willwood setup ..
17
2013/04/24 13:53:21
IMR22C

EBC Yellow part numbers

Hey just after the EBC Yellowstuff part numbers for the later model calipers?I've downloaded the EBC catalogue but can't open it. Thanks *EDIT* The numbers I've found on fleabay are DP4995R (fronts) and DP41107R (rear)..

2013/03/27 13:37:16

<< ..7 8 9 - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account