Go back to home

Community Stats
1 day 7 days 30 days Max. View More
Top Posters
  1. AnaMaria
    (3 Recent Posts)
  2. grayman
    (2 Recent Posts)
  3. Sivocci
    (1 Recent Post)
Most Active Threads
  1. Which MR2 to buy?
    (3 Replies)
Top Rated Posts
    There is no record available at this moment
Birthdays
12/6/2025
Initial_G (33)
my mr2 pollock (60)
ctung2 (36)
2007/01/05 16:30:27
Road and Track

engines available as of may 07

various engines available with various levels of rebuild. Please email us directly if you have a specific interest. Can sell most of them outright or exchange. None of them have ancillaries like starter, alternators or manifolds. Note, "short" means no head,

4AGZE. short motor , block honed & decked, good factory std pistons, crank ground, new rings bearings, seals, gaskets, oil pump , timing belt& roller. can fit a head if required, but I dont have any GZE cams.

4AG . long motor, 86KW version (early AW11). long motor, block honed & decked, crank ground, new rings, bearings, seals, gaskets, oil pump , timing belt& roller, head overhauled with valves & seats cut as required

4AG . long motor, 92KW version (later AW11). long motor, block honed & decked, crank ground, new rings, bearings, seals, gaskets, oil pump, timing belt& roller. head overhauled with valves & seats cut as required

4AG . long motor, 92KW version (later AW11). long motor, block honed & decked, crank ground, new rings, bearings, seals, gaskets, oil pump, timing belt& roller. head overhauled with valves & seats cut as required
4AG 20 valve long motor, modiferd cams, new rings, bearings, saals etc valves cut, reshimmed

4AG . long motor, 92KW version (later AW11). long motor, block bored & decked, crank ground, new pistons, rings, bearings, seals, gaskets, oil pump, timing belt& roller, head fully overhauled with valves & seats cut as required, new exhaust valve guides.

4AG big port cylinder head. Original Group A high compression head. valves & seats all recut, new seals

7AG20 valve. currently under construction. full race spec, nitrided crank, special roids, flowed black-top head and quad throttles etc etc


3SGE Gen 2,long motor SW20. block bored & decked, crank ground, new pistons, rings, bearings, seals, gaskets, timing belt& rollers, water pump. head fully overhauled with new guides, valves & seats cut as required.

3SGTE Gen 2,long motor SW20. block bored & decked, crank ground, new pistons, rings, bearings, oil pump, seals,timing belt& rollers, water pump, gaskets. head fully overhauled with new guides, valves & seats cut as required.

3SGTE Gen 3, short motor SW20. block bored & decked, crank ground, new pistons, rings, bearings, oil pump, seals, timing belt& rollers, water pump, gaskets.



15 comments Leave a comment
blobnroar
sorry im a bit of a newb and am not so sure what is meant by short and long block.
2007/01/05 21:41:31
Road and Track
short means no cylinder head. see note above
2007/02/05 08:19:14
duff_boy
How much is a 3sgte long motor worth?
2007/02/05 18:05:19
Road and Track
PM sent
2007/02/05 20:26:51
blobnroar
ok how many of these do you hav left and what prices are the long blocks if you have any left.
2007/09/05 13:41:15
Road and Track
thanks for enquiry, but you have not told me what engines you are interested in. I had 1 of each of those listed, except 3SGTE where I had 2. some look like they have sold.
2007/10/05 18:55:15
dsjoyce
How much for the 4agze?
2007/11/05 12:44:38
dsjoyce
Also i might ask, what's a rough price for installation (assuming it all goes to plan - remove old engine, swap any bits that need swapping, put new engine in?

Cheers!
2007/05/13 18:14:37
Road and Track
assuming its a 4AGZE AW11, then to swap over gearbox clutch etc, change the "short" motor, and fix-up/machine current head will take around 20 hours work plus a handful of parts. we always recommend the radiator is removed and cleaned, and any hoses showing signs of decay (most usually), are also changed. considering all that, allow $2000
2007/05/15 09:23:07
dsjoyce
Ok thanks for that, guess i'd better start counting my pennies!
2007/05/15 12:04:47
thitch2
Terry can you tell me what the Gen 2 3SGTE long cost is please.
Thanks
Phil
2007/05/22 16:34:39
Road and Track
PM's sent as requested.
2007/05/29 08:56:18
Camel
Hey guys could you PM me some more details re:

"4AG 20 valve long motor"

Price and any other details you might have close to hand.

Cheers.
2007/05/29 09:58:32
Road and Track
all engines now committed. I'll delete this post after a month or so andf then do a new one in a few months once stocks build up. in the meantime, just ask if you want something.
Please be aware however, we mostly sell rebuilt or reconditioned engines. these are always much more expensive than used engines out of imports/wrecks etc. we have good contacts with local importers so we can supply used engines, but they have limited warranty.
2007/01/07 16:53:04
Road and Track
all engines now committed. I'll delete this post after a month or so andf then do a new one in a few months once stocks build up. in the meantime, just ask if you want something.
Please be aware however, we mostly sell rebuilt or reconditioned engines. these are always much more expensive than used engines out of imports/wrecks etc. we have good contacts with local importers so we can supply used engines, but they have limited warranty.
2007/01/07 16:53:14

Comments are closed.

© 2025 APG vNext Trial Version 5.5