Go back to home

gen2 to gen3 swap, not running no spark!!

Author
Post
Essentials Only Full Version
mayheMr2
MR2 Enthusiast
  • Total Posts : 9
  • Scores: 0
  • Reward points: 2525
  • Joined: 2011/04/07 19:51:15
  • Status: offline
2013/05/12 19:43:22 (permalink)
0

gen2 to gen3 swap, not running no spark!!

Hey guys, I recently had my sw20 gen2 3sge engine/loom/ECU replaced with gen3 3sge.
 
My mechanic has encountered a problem where the car wont start due to no spark, and no power getting to the ignition coil.
 
Originally we were attempting to use my old gen2 ECU to run the car, But then realised it would be easier to Use the gen3 ECU. I recently bought an NA ECU for a gen3 from a forum user here, and hes guaranteed me that the ECU is in working order.
 
also wondering about the 4-wire plug coming off the engine loom, it doesnt appear to lead to anything, and is a new addition on the gen3. Wondering if its for the speedo-drive?
 
Is there a specific way to check if the ECU is in good condition? and does anyone have access to gen2/gen3 engine wiring diagrams?
 
much appreciated if anyone can offer help
 
 
#1


4 Replies Related Threads
    Gatesys SW20
    Supporter
    • Total Posts : 1106
    • Scores: 22
    • Reward points: 1110
    • Joined: 2012/11/06 19:28:18
    • Status: offline
    Re: gen2 to gen3 swap, not running no spark!! 2013/05/12 21:54:43 (permalink)
    0
    Not sure what your problem could be, dodgy coil pack?
    Or is there no power traveling at all to the coil?

    But my question is
    How much was your bill
    I'm thinking of doing something similar
    But luckily I work at toyota so I can get mates rates so to speak

    But was just wondering for reference
    #2
    Tree
    MR2 Deity
    • Total Posts : 1334
    • Scores: 98
    • Reward points: 2970
    • Joined: 2011/04/07 19:51:15
    • Location: VIC, S.E.
    • Status: offline
    Re: gen2 to gen3 swap, not running no spark!! 2013/05/12 22:16:24 (permalink)
    0
    ECU is usually pretty hardy and yeh use the Gen 3 one. It's normally the wiring that is the tricky bit. You can open it up to check the board isn't fried. Otherwise sent it to an electrician but before that:
    Mechanically, you wanna check
    Spark - plugs, coil, wires, dizzy in good condish
    Air - check vacuum leaks
    Fuel - listen if fuel pump is working
     
    I have gen 2 diagram i think, check this link
    https://dl.dropboxusercon...GE_WIRING_DIAGRAMS.pdf

    ex-BEAMS!
    https://www.youtube.com/p...PghBHBhC54Ftehx8yO2FsU
    #3

    artymr2
    MR2 Deity
    • Total Posts : 1105
    • Scores: 45
    • Reward points: 7867
    • Joined: 2011/04/07 19:51:15
    • Location: WA
    • Status: offline
    Re: gen2 to gen3 swap, not running no spark!! 2013/05/12 22:46:43 (permalink)
    0
    did you swap the gen3 engine wiring loom over?  If so and if it is similar to the turbo versions, it could be the same issue I had going gen 2 to 3 with 3stge, one of the wiring plugs in the engine bay fuse box, where the engine loom plugs in o the body loom, you will probably find that one of the wire locations needs a power feed.  ie the eingine loom has the ignition power wire, but the car part does not have a power feed in that pin.  worth a check and easy to do.
     
    Also make sure the coil etc are mounted properly, I was told they are earthed through the chassis.
     
    Cheers

    Black SW20 GT Turbo T-top


    #4
    mayheMr2
    MR2 Enthusiast
    • Total Posts : 9
    • Scores: 0
    • Reward points: 2525
    • Joined: 2011/04/07 19:51:15
    • Status: offline
    Re: gen2 to gen3 swap, not running no spark!! 2013/05/13 21:49:14 (permalink)
    0
    hey artyMR2 just wanted to say thanks for the information on the extra plugs in the engine bay fuse box. My car now has spark!! thanks for the quick replies guys.
    #5
    Jump to:
    © 2025 APG vNext Trial Version 5.5