purple5ive
MR2 Deity
- Total Posts : 2337
- Scores: 45
- Reward points: 2132
- Joined: 2011/04/07 19:51:15
- Location: melbourne vic Australia
- Status: offline
Ball joint Bolts and Longer wheel studs
guys, looking for a whole set (front and back) of ball joint bolts for a SW20 the ones thats hold them in place thats go on the sides i will be removing the roll centre adjusters i have (these came with longer bolts to accomodate the extra height) once they were fitted i lost the oroginal bolts that were on there, looking to replace them back. Also looking for 5mm longer wheel studs so i can use my spacers properly anyone can help me out that would be good. cheers
post edited by purple5ive - 2013/03/25 10:29:21
|
purple5ive
MR2 Deity
- Total Posts : 2337
- Scores: 45
- Reward points: 2132
- Joined: 2011/04/07 19:51:15
- Location: melbourne vic Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 10:31:02
(permalink)
ALSO after some longer wheel studs as well now
cheers
|
B24
Supporter
- Total Posts : 2405
- Scores: 278
- Reward points: 5936
- Joined: 2011/04/07 19:51:15
- Location: Sydney NSW Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 11:04:51
(permalink)
There is a company called 'nice products' in Sydney. They have whatever you need. It is where I bought my longer studs. http://www.niceproducts.com.au/catalogues/wheel/wheel.phpAny engineering supplier will have the ball joint bolts. They are 10 x 1.5 on the front and 12 x 1.5 on the rear. Not sure on lengths but 40mm overall should do the job. Make sure they are high tensile.
|
robk
MR2 Deity
- Total Posts : 2172
- Scores: 314
- Reward points: 5229
- Joined: 2011/04/07 19:51:15
- Location: Sydney / Central Coast, NSW Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 11:18:08
(permalink)
FYI, on the rear of my car I used Dorman 610-445 wheel studs which are 9mm longer than stock. I installed them in the typical way and they pulled in to the hub quite easily with a corded electric impact wrench.
|
purple5ive
MR2 Deity
- Total Posts : 2337
- Scores: 45
- Reward points: 2132
- Joined: 2011/04/07 19:51:15
- Location: melbourne vic Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 11:39:37
(permalink)
Thanks guys .
Steve - do you know how much longer the NIce studs are?
Rob thanks 9mm is good for a 10mm speacer i thnk awsome. where do i find these Dorman branded studs
i am running 5mm spacers atm allover.
also im assuming the Knurl length and diameter are the same as stock?
|
robk
MR2 Deity
- Total Posts : 2172
- Scores: 314
- Reward points: 5229
- Joined: 2011/04/07 19:51:15
- Location: Sydney / Central Coast, NSW Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 11:56:55
(permalink)
purple5ive
Thanks guys .
Steve - do you know how much longer the NIce studs are?
Rob thanks 9mm is good for a 10mm speacer i thnk awsome. where do i find these Dorman branded studs
i am running 5mm spacers atm allover.
also im assuming the Knurl length and diameter are the same as stock?
http://www.dormanproducts.com/p-15988-610-445.aspxThe knurl diameter is a tiny bit bigger than stock (14.48mm compared to 14.20mm), which is why I mentioned that I still had no trouble installing them. I think I got mine on eBay from the US, which was a bit of a waste due to the shipping cost, but it wasn't excessive so I didn't mind.
|
B24
Supporter
- Total Posts : 2405
- Scores: 278
- Reward points: 5936
- Joined: 2011/04/07 19:51:15
- Location: Sydney NSW Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 13:55:18
(permalink)
Nice has all the spec's in their catalogue. They have the right knurl sizing with three different sizes available for the Toyota. Mine are 75mm.
I would not advise 10mm spacers. I had a bad experience with these a few years back. Safer to change your rims with a different offset to suit your application than space it out too much.
Rob, its not the best way to fit the studs as they can and do stretch/weaken. Best way is to access a press to fit the new studs.
|
robk
MR2 Deity
- Total Posts : 2172
- Scores: 314
- Reward points: 5229
- Joined: 2011/04/07 19:51:15
- Location: Sydney / Central Coast, NSW Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 14:12:24
(permalink)
B24
Rob, its not the best way to fit the studs as they can and do stretch/weaken. Best way is to access a press to fit the new studs.
Yeah I know it's not the 'best' way, but many people do it that way and I just wanted to get it done without taking too many things apart.
|
Reddtarga
MR2 Deity
- Total Posts : 2175
- Scores: 249
- Reward points: 5547
- Joined: 2011/04/07 19:51:15
- Location: Vic Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 17:06:30
(permalink)
Steve (purple), why not get new genuine Toyota ball joint studs.
Lithia Toyota have them.
Front P/N 90105 10129 $2.56 ea USD (4 needed)
Rear P/N 90105 12059 $1.95 ea (4 needed)
Probably not that much more from the local dealers.
Longer wheel studs:
Being longer, they will also be under more stress than stock length studs, and to fit them with a press you would need to remove the hubs from the car.
A lot of work, but probably a good idea since your wheels will hang on the studs alone. (since your hub rings will be useless).
|
purple5ive
MR2 Deity
- Total Posts : 2337
- Scores: 45
- Reward points: 2132
- Joined: 2011/04/07 19:51:15
- Location: melbourne vic Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 19:49:41
(permalink)
Ian , i think theres just enough hub left for the hub centre cap to hold onto otherwise i woudnt have left it in there. otherwise when centering the wheel they would already be hanging on the wheel studs and would have been hard to put the wheel bolts back on, i checked them and each stud is located in the centre of the wheels PCD holes, which means the hub centric spacer/adapter is doing its job but by a hairs thickness but yeah might make up some better hub centric spacers when there some more time up my sleeve. i asked toyota locally - they have to order from japan at $6 each. might be able to get it cheaper as the guy i spoke to isnt my regular dealer. thank s for those part number will come in handy when i speak to them next time cheers
post edited by purple5ive - 2013/03/25 20:08:45
|
kameleon
Supporter
- Total Posts : 2733
- Scores: 106
- Reward points: 6018
- Joined: 2011/04/07 19:51:15
- Location: melbourne vic Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 20:43:01
(permalink)
Winding the studs in on the car manually works fine, using what is effectively a hammering ratchet is not the best idea for getting something to seat hahahaha. It obviously worked though!
|
purple5ive
MR2 Deity
- Total Posts : 2337
- Scores: 45
- Reward points: 2132
- Joined: 2011/04/07 19:51:15
- Location: melbourne vic Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/25 21:04:05
(permalink)
hasnt been done yet Trav. hopefully soon.
|
Road and Track
MR2 Master
- Total Posts : 1427
- Scores: 29
- Reward points: 3770
- Joined: 2011/04/07 19:51:15
- Location: Ipswich, Queensland, Australia Queensland Australi
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/03/31 12:32:47
(permalink)
we have all this in stock.
Road & Track For more information and contact details for Road & Track, clickHERE
|
Reddtarga
MR2 Deity
- Total Posts : 2175
- Scores: 249
- Reward points: 5547
- Joined: 2011/04/07 19:51:15
- Location: Vic Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/04/06 12:38:02
(permalink)
|
fredhoon
MR2 Master
- Total Posts : 368
- Scores: 26
- Reward points: 5537
- Joined: 2011/04/07 19:51:15
- Location: Brisbane Qld Australia
- Status: offline
Re: Ball joint Bolts and Longer wheel studs
2013/04/06 15:08:40
(permalink)
I've got 2x sets of the ARP longer wheel studs (bought from TwosRus) if your interested. From memory I think they are around 25mm longer though, so they may not suit your application. [edit] from the MR2OC thread above, I believe these are the studs I have in a box somewhere... MR2OCARP 100-7715 Lexus IS300
Knurl diameter: .558" (14.173mm)
Shoulder length: .230" (5.842mm)
Length: 2.60" (66.04mm)
Thread pattern: M12x1.5
post edited by fredhoon - 2013/04/06 15:25:12
 Go soothingly on the grease mud as there lurks a skid demon.
|