Go back to home

sw20 crank pulley/ harmonic ballancer

Author
Post
Essentials Only Full Version
71meh
MR2 Enthusiast
  • Total Posts : 34
  • Scores: 0
  • Reward points: 3835
  • Joined: 2012/01/15 20:21:18
  • Location: Townsville, Queensland
  • Status: offline
2012/06/17 21:53:55 (permalink)
0

sw20 crank pulley/ harmonic ballancer

Hey guys,
 
Just after one of these as the one on the mr2 engine i have the bolt is mega tight/siezed and cannot crack it with rattle gun, heating it. Any ideas?
 
or just one in good condition and express post
 
Cheers,
Tim
#1


9 Replies Related Threads
    dasic1
    Moderator
    • Total Posts : 1323
    • Scores: 83
    • Reward points: 5910
    • Joined: 2011/04/07 19:51:15
    • Location: melbourne vic Australia
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/17 22:13:41 (permalink)
    0
    Is it still in the car?

    https://www.facebook.com/MuscleMotorTrimmers
     
    SW20 bits for sale
    http://www.mr2australia.c./mr2play/tm.aspx?m=68510
    #2
    71meh
    MR2 Enthusiast
    • Total Posts : 34
    • Scores: 0
    • Reward points: 3835
    • Joined: 2012/01/15 20:21:18
    • Location: Townsville, Queensland
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/17 22:14:41 (permalink)
    0
    I wish, if it were id use the starter motor to crack the bolt.
     
    its on the ground no gearbox attached
    #3

    Reddtarga
    MR2 Deity
    • Total Posts : 2175
    • Scores: 249
    • Reward points: 5547
    • Joined: 2011/04/07 19:51:15
    • Location: Vic Australia
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/18 10:14:46 (permalink)
    0
    I found that even a good rattle gun was no good for my motor that was on an engine stand.
    A good 6 sided inpact type socket was needed so as not to burr the nut.
    Because I was worried that the socket would slip off just using a long breaker bar, I used a "T" socket connector with pipe lengths over the ends, and one person on each with the flywheel ring gear chocked.
    Boy was I happy when that sucker cracked!!
    post edited by Reddtarga - 2012/06/18 10:20:14

    1990 ADM NA
     
     
     
     
     
     
    #4
    Mrskylighter
    MR2 Deity
    • Total Posts : 2156
    • Scores: 174
    • Reward points: 6592
    • Joined: 2011/04/07 19:51:15
    • Location: NSW Australia, Hills District
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/18 10:37:15 (permalink)
    0
    I have a spare Gen 2 3sgte Celica crank pulley.  Not sure if that would help you.
    It is 5 rib whereas the MR2 is 4 rib.
     
    Cheers, 
    #5
    just_ace
    Moderator
    • Total Posts : 2508
    • Scores: 89
    • Reward points: 4598
    • Joined: 2011/04/07 19:51:15
    • Location: perth wa Australia
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/18 11:16:25 (permalink)
    0
    i'll check when i get home tonight..
     
    heavy bugger, but if under 5kg i think the express bag is approx $20
    #6

    71meh
    MR2 Enthusiast
    • Total Posts : 34
    • Scores: 0
    • Reward points: 3835
    • Joined: 2012/01/15 20:21:18
    • Location: Townsville, Queensland
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/18 21:47:22 (permalink)
    0
    I have a gen2 celica one here already, the inside is for the 4 groove (power steering pump on celica), where as i need the 5 groove for the alternator on mr2, 
     
    just_ace - Let me know how you go mate
     
    Cheers,
    Tim
    #7
    just_ace
    Moderator
    • Total Posts : 2508
    • Scores: 89
    • Reward points: 4598
    • Joined: 2011/04/07 19:51:15
    • Location: perth wa Australia
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/18 22:39:13 (permalink)
    0
    yeh i have one. PM addy details and i'll post tomo
    #8
    MRVirgin
    MR2 Aficionado
    • Total Posts : 786
    • Scores: 13
    • Reward points: 2709
    • Joined: 2011/04/07 19:51:15
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/18 22:53:04 (permalink)
    0
    I had the same problem with the crank pulley on my 1mz. In the end I borrowed a 3/4" rattle gun and had it off in a few seconds. I had been hanging off a breaker bar and hammering away fruitlessly with a 1/2" gun for what seemed like hours.
    #9
    71meh
    MR2 Enthusiast
    • Total Posts : 34
    • Scores: 0
    • Reward points: 3835
    • Joined: 2012/01/15 20:21:18
    • Location: Townsville, Queensland
    • Status: offline
    Re:sw20 crank pulley/ harmonic ballancer 2012/06/19 18:48:30 (permalink)
    0
    All sorted, have one on the way.
     
    Cheers,
    Tim
    #10
    Jump to:
    © 2025 APG vNext Trial Version 5.5