Go back to home

Gearbox, SW20

Author
Whore of Babylon
MR2 Aficionado
  • Total Posts : 644
  • Scores: 12
  • Reward points: 5676
  • Joined: 2011/04/07 19:51:15
  • Location: Devonport Tasmania Australia
  • Status: offline
2010/05/13 21:42:32 (permalink)
0

Gearbox, SW20

Hey im in the market for a N/A gearbox i have shafts. Dont need anything special either, just a working box. In no rush either so let me know

Also after an engine manual for a 3SGE,

Cheers
WoB
#1


7 Replies Related Threads

    Road and Track
    MR2 Master
    • Total Posts : 1427
    • Scores: 29
    • Reward points: 3770
    • Joined: 2011/04/07 19:51:15
    • Location: Ipswich, Queensland, Australia Queensland Australi
    • Status: offline
    RE: Gearbox, SW20 2010/05/21 09:04:00 (permalink)
    0
    if you are still looking I should be able to help, but is it worth freight to tas??.
    #2
    Whore of Babylon
    MR2 Aficionado
    • Total Posts : 644
    • Scores: 12
    • Reward points: 5676
    • Joined: 2011/04/07 19:51:15
    • Location: Devonport Tasmania Australia
    • Status: offline
    RE: Gearbox, SW20 2010/05/26 09:25:10 (permalink)
    0
    Well it might be, my shopping list is:

    N/A Gearbox
    1990 3SGE (full) Gasket kit
    Waterpump
    oilpump
    timing belt
    also, on a >200,000km engine i was going to do the rings but do you recon its worth doing the pistons, rings and conrods?

    cheers
    #3

    Road and Track
    MR2 Master
    • Total Posts : 1427
    • Scores: 29
    • Reward points: 3770
    • Joined: 2011/04/07 19:51:15
    • Location: Ipswich, Queensland, Australia Queensland Australi
    • Status: offline
    RE: Gearbox, SW20 2010/05/30 19:18:17 (permalink)
    0
    at 200K, there may be considerable piston to bore clearance. typically #3 cylinder is out-of-round. if you just want a patch up, a re-ring might work, but dont expect it to last another 200k

    i am reluctant to sell as-is gearboxes as OK today, crappy tomorrow. you can never please people.

    I will do you a job lot deal on a box thats been stripped & fitted with new 2nd & 3rd syncros & all new seals , plus new engine gasket kit, water pump, timing belt, oil pump gear kit, all for $1700
    #4
    Senol
    MR2 Scholar
    • Total Posts : 1111
    • Scores: 21
    • Reward points: 2497
    • Joined: 2011/04/07 19:51:15
    • Location: Brisbane Queensland Australia
    • Status: offline
    RE: Gearbox, SW20 2010/07/31 00:30:07 (permalink)
    0
    im looking for a s54 gearbox too.. If I can get a cusco type RS (i found a company that can supply them) would you be able to fit it? I honestly couldnt be bothered pulling my current gearbox apart seing that they arent worth much anyway. I also need another mechanical speedo the one that plugs into the box.
    #5
    Road and Track
    MR2 Master
    • Total Posts : 1427
    • Scores: 29
    • Reward points: 3770
    • Joined: 2011/04/07 19:51:15
    • Location: Ipswich, Queensland, Australia Queensland Australi
    • Status: offline
    RE: Gearbox, SW20 2010/07/31 19:29:30 (permalink)
    0
    no trouble to fit a LSD, but it requires a complete strip down and 2 new diff side bearings (as a minimum)
    #6

    Senol
    MR2 Scholar
    • Total Posts : 1111
    • Scores: 21
    • Reward points: 2497
    • Joined: 2011/04/07 19:51:15
    • Location: Brisbane Queensland Australia
    • Status: offline
    RE: Gearbox, SW20 2010/01/08 12:14:08 (permalink)
    0
    How much would it be for fitting differential? I can just exchange my gearbox too (to reduce the cost) if you have one there thats lying around in good condition. as for the sidegears i think they are about $50 each new from toyota.
    #7
    Road and Track
    MR2 Master
    • Total Posts : 1427
    • Scores: 29
    • Reward points: 3770
    • Joined: 2011/04/07 19:51:15
    • Location: Ipswich, Queensland, Australia Queensland Australi
    • Status: offline
    RE: Gearbox, SW20 2010/01/08 19:23:38 (permalink)
    0
    best to phone me to discuss
    #8
    Jump to:
    © 2025 APG vNext Trial Version 5.5