petmr2
MR2 Enthusiast
- Total Posts : 142
- Scores: 2
- Reward points: 493
- Joined: 10/6/2015
- Status: offline
Thursday, September 22, 2016 10:58 PM
(permalink)
No front lip
Anyone have any pics of MR2 without front lip? I'm curious to know if it looks good without it?
|
Fast Eddie
MR2 Deity
- Total Posts : 268
- Scores: 57
- Reward points: 4172
- Joined: 2/15/2013
- Location: Penrith NSW
- Status: offline
Re: No front lip
Friday, September 23, 2016 1:11 AM
(permalink)
PM your mobile number and i'll flick you a photo as mine is off at the moment.
|
dylmrt
Vendor
- Total Posts : 2156
- Scores: 111
- Reward points: 6118
- Joined: 4/7/2011
- Location: NSW Australia
- Status: offline
Re: No front lip
Friday, September 23, 2016 1:51 AM
(permalink)
|
petmr2
MR2 Enthusiast
- Total Posts : 142
- Scores: 2
- Reward points: 493
- Joined: 10/6/2015
- Status: offline
Re: No front lip
Friday, September 23, 2016 1:53 AM
(permalink)
The OEM front bumper I purchased doesn't have front lip and from the pic from Fast Eddie, it looks good.. Is there a reason why you think its a bad idea?
|
dylmrt
Vendor
- Total Posts : 2156
- Scores: 111
- Reward points: 6118
- Joined: 4/7/2011
- Location: NSW Australia
- Status: offline
Re: No front lip
Friday, September 23, 2016 2:58 AM
(permalink)
You'll find over time the bottom of the bar will sag, its very thin plastic and the whole bumper will start to lose shape.
|
Fast Eddie
MR2 Deity
- Total Posts : 268
- Scores: 57
- Reward points: 4172
- Joined: 2/15/2013
- Location: Penrith NSW
- Status: offline
Re: No front lip
Friday, September 23, 2016 3:06 AM
(permalink)
Mine is only off because its going into the workshop and its to low to get into there driveway. You need the lip that's what all your under plastics attach to give it support.
|
Shaz
Supporter
- Total Posts : 1434
- Scores: 226
- Reward points: 5852
- Joined: 11/5/2012
- Location: Newcastle
- Status: offline
Re: No front lip
Friday, September 23, 2016 3:11 AM
(permalink)
This is mine. Stock. Always been like this I think.
|
petmr2
MR2 Enthusiast
- Total Posts : 142
- Scores: 2
- Reward points: 493
- Joined: 10/6/2015
- Status: offline
Re: No front lip
Friday, September 23, 2016 3:25 AM
(permalink)
Ah I see... Ok I'll have to save up and order the front lip then
|
rikkir
Supporter
- Total Posts : 1286
- Scores: 242
- Reward points: 2404
- Joined: 1/13/2014
- Location: Ceduna, South Australia
- Status: offline
Re: No front lip
Friday, September 23, 2016 5:13 AM
(permalink)
Silver 1997 SW20 Bathurst with
|
Reddtarga
MR2 Deity
- Total Posts : 2175
- Scores: 249
- Reward points: 5547
- Joined: 4/7/2011
- Location: Vic Australia
- Status: offline
Re: No front lip
Friday, September 23, 2016 7:02 AM
(permalink)
The later model 02+ 92+ front lips also need the correct hardware set to mount them. There are about 6 plates/strips you need, without which it will be a PITA to try and mount. 76863-17040 76864-17020 76857-17020 76858-17020 76853-17020 76861-17020
post edited by Reddtarga - Friday, September 23, 2016 11:39 PM
|
petmr2
MR2 Enthusiast
- Total Posts : 142
- Scores: 2
- Reward points: 493
- Joined: 10/6/2015
- Status: offline
Re: No front lip
Friday, September 23, 2016 8:18 AM
(permalink)
Really even even eBay front lip? Would that require these parts . Well
|
Reddtarga
MR2 Deity
- Total Posts : 2175
- Scores: 249
- Reward points: 5547
- Joined: 4/7/2011
- Location: Vic Australia
- Status: offline
Re: No front lip
Saturday, September 24, 2016 0:04 PM
(permalink)
Re-read dylmrt's post. Those front lips have no stiffness on their own, so the proper hardware is needed to keep the the whole lower bumper edge stiff with the correct shape. Bolts and washers on their own won't do that.
|
petmr2
MR2 Enthusiast
- Total Posts : 142
- Scores: 2
- Reward points: 493
- Joined: 10/6/2015
- Status: offline
Re: No front lip
Saturday, September 24, 2016 10:06 AM
(permalink)
So is this hardware required for both gen 2 or gen 3 lip?
|
Carmikey
MR2 Deity
- Total Posts : 1969
- Scores: 260
- Reward points: 6437
- Joined: 4/23/2012
- Location: Greenwith 5125, S.A. Australia
- Status: offline
Re: No front lip
Saturday, September 24, 2016 11:15 AM
(permalink)
petmr2 So is this hardware required for both gen 2 or gen 3 lip?
yep.
|
Richieyellowmr2
MR2 Enthusiast
- Total Posts : 86
- Scores: 3
- Reward points: 1489
- Joined: 7/16/2016
- Status: offline
Re: No front lip
Friday, December 02, 2016 11:49 AM
(permalink)
Where can i buy hardware from 6 plates/strips .
|