Engines / Exhausts / Gearboxes / Differentials

To Bottom

Engines / Exhausts / Gearboxes / Differentials (p.6)
Post New Thread
Regular
Flyboy

Help with B pipe suitability

Hey guys,can someone tell me if this is the correct flange bolt pattern to suit my Rev 3 CT20B turbo?I'm looking to buy this pipe and match it up with a new Legalis R system.(see pic)..
2
2019/11/22 00:33:00
Eric

WIP - Comprehensive Aussie 2GR Swap Guide

Work in progress - Please feel free to contribute any info below Hi All. The 2GR swap. Probably the best V6 swap we can currently do. Great power, reliability (except for my alternator problems) and an amazing sound. You will smoke tyres and have an absolute blast. But, this is not an easy swap. ..
28
2019/10/26 19:36:36
Dalai

White smoke under load, no boost and now dead!

I realise that it is near impossible to diagnose online, but currently sitting in the car waiting for a tow truck. With an estimated 90 minutes to 2 hours wait, I thought I would use some of that time and ask the brains trust! Car is a December 92 JDM hardtop turbo. Nothing fancy with the engine ..
5
2019/10/18 07:35:28
tuban

new CT26 turbo

Hi,thought I'd document my purchase of a Chinese CT26 turbo and how the saga goes. I was looking at CT26 rebuild kits on Ebay and found a new turbo for $399 including postage. There are a number of CT26 turbos on Ebay but most are not for MR2, different flange shape etc but this one looked good. See..
24
2019/10/17 07:43:28
tuban

clutch linkage failure

Hi, if you've had intermittent clutch pedal travel issue and fluids all look OK have a look at the linkage between the pedal arm and the master cylinder. Mine had fractured and sometimes gave bad pedal travel. Give the linkage a bit of a push up/down and sideways to see if there is movement...
4
2019/10/08 20:07:25
GTIRHil

Camshaft timing problem

HiI read lots of good stuff on camshaft timing but I still can't get it to work.I skimmed a bit off my head and got adjustable (Blox) cam gears, as advised by the shop. I still have stock cams in my 1989 AW11 with big port 4AGE, , so according to Bob Sherwood I am looking to reach full exhaust openi..

2019/10/07 18:29:11
Exfaz

ZZW30 SPYDER SMT:

Hi forum members...Shudders from cold start in first gear going forward. If I warm up motor alternately selecting forward and reverseissue improves. Have 'sucked' out SMT fluid and replaced with no real improvement. Hope somebody has experienced similar...

2019/07/02 16:59:06
Admin

CT26 and CT20b compatibility

I'm going to remove my high flowed CT26 from my MR2 race car soon, and I was thinking about fitting it to my ST205 GT4, which (I think) has a standard CT20b.Are they a straight swap? If not, what needs to be changed?Thanks...
7
2019/06/20 19:40:06
Matts_SW20

Turbo loosing psi after fast drive

Hi Brains Trust, Been having this issue for a while. I have a 3S with a CT26 and Electronic Boost Controller and Fuel Cut Defender. 90% of the time it boosts perfectly and responds perfectly. But after I drive it hard and do some hard cornering and boosting the engine drops the psi of the turbo. It'..
19
2019/06/06 21:33:43
maccardo94

Oil in exhaust downpipe after return/feed lines

Hi guys Recently changed my turbo oil return/feed lines to braided 10an for the return. Install went well but upon startup after install i now have white smoke puffing from the exhaust and wont go away not even after 10min idle. Upon inspection seems oil is seeping from the exhaust downpipe and tur..
11
2019/06/05 10:25:54

<< ..4 5 6 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account