Engines / Exhausts / Gearboxes / Differentials

To Bottom

Engines / Exhausts / Gearboxes / Differentials (p.27)
Post New Thread
Regular
lachyduwakin

Performance Exhaust

I was just wondering on the best place for a performance exhaust to fit a sw20 non turbo mr2 having a hard time trying to find one..
2
2015/04/05 19:11:23
turbomr2

Turbo exhaust housings

Hey all, Please provide valid input on Tial stainless steel turbo housing VS Garrett cast iron... "borrowed pic"..
6
2015/04/02 02:06:26
FerociousSnail

Gen2 3SGE dimensions

Hi! Just wondering if there's anyone that knows the dimensions of a Gen2 3SGE compared to a Gen5 BEAMS blacktop? I have the BEAMS dimensions, just having trouble finding the Gen2. Is it just be the head height that's different? Obviously the intake is huge but just after the basic engine (head and b..

2015/03/31 20:56:48
Carmikey

WTB: Knock sensor 3sgte. **Purchased**

Does anyone have a 'Knock sensor' for a 3sgte, or 3sge? (not sure if they are the same part no. though).Does anyone know the part no. for one of these? When rebuilding the engine, I accidently cracked the plastic bit on the knock sensor. These are the numbers I can see. 04075, & 66014 on the oth..
12
2015/03/30 14:13:22
MR PLOW

Turbo upgrade ideas?

Hi folks,Following my turbo dramas over the last few months, I'm planning on upgrading the turbo. Currently has a hi-flowed ct26, was rebuilt, but suffers now from an exhaust seal leak, and poor overall suitability (compressor surge at mid rpm on-boost, slow to spool etc). I'm over it.Car is not my ..
12
2015/03/24 22:12:39
Dektra

3VZFE --> SW20

Hey MR2 Australia! First post! Now that I've got that out of my system onto the things that matte... I've bought myself a 1993 (n/a gen 2) sw20 with dreams of building a time attack race dedicated car. First things first, 3VZFE, from what I've read this is probably one of the better V6s to go with a..
7
2015/03/24 18:10:41
stuka

Aftermarket E153 Gearbox Oil Cooler Placement

There doesnt seem to be a lot of information out there in regard to aftermarket gearbox oil coolers. Does anyone have any photos or guides on oil cooler placement to ensure decent airlflow through it without risking damage from debris etc?..
3
2015/03/21 23:38:51
PeteClarky

Inconsistent Idle

After having a Greddy boost controller & HKS fuel cut defender installed my idle is quite irregular. - If I change from 1st to 2nd, when I clutch in the revs don't drop- Sometimes in other gears when I clutch in the revs won't drop (until I blip the accelerator)- Sometimes drops too low and bogs..

2015/03/21 14:30:32
Mrskylighter

HUX Racing Honda K20/24 bolt in swap kit for SW20 available

Hi all, Was just reading on MR2OC that Eric Hux has his Honda K20/24 bolt in swap kit ready for sale now. $1500 and it uses your existing E153, axles etc.More info can be found here. http://www.mr2oc.com/showthread.php?p=5387098#post5387098 Thought some of you guys might be interested. Peace out. ht..
15
2015/03/13 13:08:30
IMR22C

Any machine shop experts?

G'day, as some of you might know. My engine dropped oil pressure and has been since torn down. Unfortunately I didn't catch it as early as I was hoping and subsequent scoring has occurred on the crank, bores, and cams (incl. journals) The machine shop says that the bottom end is saveable, but the ca..
4
2015/03/13 08:15:55

<< ..25 26 27 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account