Body Kits / Paint / Panel

To Bottom

Body Kits / Paint / Panel (p.7)
Post New Thread
Regular
AmeR

Carbon Fibre Bonnet

Has anyone in VIC fitted one to a Spyder and had it approved? I am considering replacing my dented OEM bonnet with a vented CF one but don't want to pay out all the cash if it's going to end up sitting in the garage!! I've tried Google but I end up with a lot of old links filled with indefinite inf..

2014/11/13 09:43:23
Ballzy

Rear C Panel edging strips - where to buy new

Newbie here, sorry if I'm repeating a previous thread, I couldn't find the answer, again, apologies if this is old hat to everyone else. Is it possible to buy the plastic edging strips that go on the back of the C-Pillar on an AW11? The original 1988 ones just crack and fall apart when you take them..
1
2014/11/06 21:20:32
RHOK

Wing Revisions

I have the following wing on my car -- no idea what revision it is My question is -- do the revision 5 wings share the same bolt hole pattern ? http://img.pistonheads.com.s3-eu-west-1.amazonaws.com/Fullsize/toyota/mr2/toyota-mr2-S1190271-5.jpg cheers..
4
2014/10/15 11:07:14
violator

Painted targa tops

Hi.Has anyone had their glass targa tops painted?How was it done and how is the paint lasting?Other option is vinyl but I'm not sure how close they will be able to match '93 blue metallic. I see this product claims to work on glass:Bulldog® Adhesion Promoter is designed to promote paint adhesion to ..
8
2014/10/08 15:33:23
thomas108

Any hints - tail light removal and side quarter panel trim

Need to repaint the rear quarter panel of 91 sw20 model. Couple of questions before I start? Any tricks with the tail lights, hard to get to screws/clips etc? Quarter panel trim, same as above, trim is in perfect condition so I don't want to damage it?..
3
2014/09/30 23:23:31
thomas108

What is this part, where does it go?

Long story.....new radiator, condenser fitted, took front nose cone off and all under body plastic. This part dropped out, drivers side near front wheel arch and cannot work out for the life of me where it goes. Seemed to be held on with the under body panel bolts but where? Pictures attached below...
2
2014/09/21 17:32:52
adamaw11

MR2 smash repairs - recommendations in Brisbane southside

Anyone got any recommendations for panel beaters they've dealt with in Brisbane?Particularly on MR2s, any good or bad experiences, or places to recommend? I've got some damage, pretty much the rear bumper and some of its supporting metal. The guy who ran into the back of me is offering to pay for it..

2014/09/20 11:28:12
Steve_A

94+ Tails With 91+ Centre Panel: Reverse Light Location

So I've got myself a pair of Kouki tails and I'm going to fit them with the Zenki centre panel. This will require a little cutting to fit and some glassing to get a flush OEM look, but its really not too complicated. Obviously there is no provision for reverse lights in the Zenki centre panel, and I..
7
2014/08/20 13:17:25
MrPedro

Poly Urethane Front Bar

Anyone ever seen/bought one of these?: http://www.ebay.com.au/itm/Toyota-MR2-91-96-Border-Urethane-Front-Bumper-Body-Kit-/130500860689 If so any info about them would be awesome. Alternatively does anyone make Poly bodykits in Aus? Cheers...
3
2014/08/04 09:42:05
dom

WTB sw20 front lip. Melbourne

looking for front lip for sw20. preferably not the thick one i think they are called aerowarethanks...

2014/07/28 01:33:51

<< ..7 8 9 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account