2019/01/26 22:59:38
Shaz
Admin
Doesn't Deltav sell the bushing kits?

I'd already checked with Travis after Aaron mentioned them
 
Carmikey
Shaz, i got my spherical bearings from China on ebay for like $15 delivered. Fit and do the job perfectly.
Can send you details / measurements of the bearings If required.

Sent from my SM-J320ZN using Tapatalk

Not sure about Chinese, especially if I'd have to give them measurements.  At least with twosrus they are exactly the right thing.
2019/01/26 23:03:06
Lumix
I purchased my spherical kit from https://mr2wreckers.com.au/ as they are/were the Australian supplier of the CRW kits. Perhaps they still have some kits in stock?
2019/01/27 09:38:26
kojab
I bought 2 spherical bearings (p/n GEBK8S) from Industrial Bearings in Padstow for $26.40. 
They seem to fit ok and work fine.
2019/01/27 20:41:35
5SGTE
^^ I have these same bearings and it's as smooth as silk.
2019/01/28 09:55:46
Shaz
Lumix
I purchased my spherical kit from https://mr2wreckers.com.au/ as they are/were the Australian supplier of the CRW kits. Perhaps they still have some kits in stock?


Email sent to MR2 wreckers.
kojab
I bought 2 spherical bearings (p/n GEBK8S) from Industrial Bearings in Padstow for $26.40. 
They seem to fit ok and work fine.


just bearings.  Or do they come in a full kit?
Dudeman
Don't buy a chery or whatever that ting is, they are terrible. And like an aluminium can in a crash.
 
You could be buying a lot more problems with that black rev1, if it has set around for a long time a lot of the seals in just about everything may have given up.
 



wasn't really serious about the Chery or the black rev1.  
2019/01/28 10:22:35
kojab
Shaz
 
kojab
I bought 2 spherical bearings (p/n GEBK8S) from Industrial Bearings in Padstow for $26.40. 
They seem to fit ok and work fine.


just bearings.  Or do they come in a full kit?


Just bearings.  That's all I needed.  I did make up some small steel tubes to go each side of the bearings but you probably would still have some thing like this already on the end of your cables.
2019/01/29 22:56:53
Shaz
Kit ordered from MR2 Wreckers.  
 
My baby has moved to mum's garage keeping the ADUB company.  I pick up a 2012 Hyundai i20 tomorrow. 
 
2019/02/03 10:04:56
Lumix
How do you like the Hyundia i20? Chance of pace from the MR2.
2019/03/14 23:35:38
Shaz
Lumix
How do you like the Hyundia i20? Chance of pace from the MR2.


Yes it is a bit of a change, especially being an Auto too.  loses power going up long inclines.  But at least I have something of my own to drive when the MR2 is off the road. 
 
 
Sperical bearings put in last week, but didn't fix the problem .  Daniel suggested taking her to Newcastle Gearbox & Diff.  She drove mostly fine from Mum's to home, then to work, then to Broadmeadow.  She did the thing when they test drove & they have determined that it is the side/side cable but not on the gearbox end.   I asked if they could put the original back in, but they don't usually do that sort of stuff, weren't keen on taking the interior bits apart, plus don't have any spare time for the next couple of weeks.  The side/side cable that was taken out was ok, so will look to having that put back.  Mine was a white banded cable & the replacement was red, altho I had been assured that they both came out of the same NA MR2.  Mechanic said he checked & they appeared to be the same, so............. maybe not quite. 
 
Picked her back up this afternoon (no charge) & the drive back to mum's was very painful , but at least I knew what to do to get to my required destination.  Don't panic, move gearstick around in neutral & then put in gear.  But it was 5pm & there was a bit of traffic around, so wanted to be quick, so someone didn't run up my butt,  didn't always work   took off in 2nd a few times & sometimes couldn't go into 2nd from 1st, so went straight to 3rd.  Luckily no hill starts.   
 
And She'll probably be mostly fine next time.  ggrrrr
2019/03/15 22:45:19
Matts_SW20
Good to know you can at least test by re-installing the side to side cable, I'm sure your local mechanic would be able to do that. Does mean another $140 in labour or so but if it fixes the problem then happy days. 
<< ..2930.. >> - Powered by APG vNext Trial
© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Use My Social Media Account