Engines / Exhausts / Gearboxes / Differentials

To Bottom

Engines / Exhausts / Gearboxes / Differentials (p.44)
Post New Thread
Regular
track_mr2

Pod Filters and Cold Air Intakes

Here's a link to some decent back to back dyno tests on cars running pod filters, stock air boxes and cold air intakes. http://www.youtube.com/watch?v=gCi2yo4UqPI Basically saying that you lose power in an NA and no real difference in a turbo. The exceptions I believe would be with cars running larg..
7
2013/09/24 23:51:05
Dr.J

Turbo upgrade advice?

Hi everyone,so I have a Gen 3 SW20 and have been offered a GTX 2863R at a good price.What do I need to do to get it it working?Car is pretty much stock right now. Thanks in advance... :)..
13
2013/09/21 01:36:54
Ray-MR2

Noisy gearbox

Has anyone used Nulon G70 manual gearbox & diff treatment to reduce occasional noise from the transmission?If so did it work & would you recomend it?..
2
2013/09/16 20:04:04
bhm133

Accessing the valve cover 91 SW20 3gse

Hi, If in the wrong place please move/delete. Bit of frustration on what I think should be simple. I just can't figure it out. I could just go nuts and pull everything apart, but that will stress me as I like to do things properly and step by step. I have a little car experience but on old..
6
2013/09/16 17:48:19
worldwalker

4AGZE... effing loud?

Ok so after reading up on exhausts and best advice I've finished my AW11 SC exhaust. It's a 2.5in manifold back (holds 4.9in area from ports to tip) It's a good 60-80cm longer than stock and most other custom/after market, 200CPI bullet cat, a 15x4in resonator and 4x8 16in strait through muffler. Ot..
9
2013/09/03 10:18:52
dwyer125

What compression ratio should I run?

I have just assembled my block with forged ross pistons and eagle rods.I have measured the volume of the head and the volume above the piston at TDC with a sheet of perspex and syringing oil in.So I have made a quick compression ratio calculator to help determine the head gasket I should get. It use..
44
2013/08/31 14:38:48
dwyer125

What is this valve cover? Not normal

I purchased a gen3 head a long time ago and I'm just getting it on now. I went and bought new valve cover gaskets for the gen3 mr2/st205 only to find now they are wrong. (11213-88480 and 11214-88480)So I now presume it is a caldina head but the every picture i look at and also parts diagrams on toyo..
10
2013/08/21 19:14:01
dwyer125

Timing belt cover differences.

I went to order a gen3 timing belt cover today but, there are 3 part numbers.the mr2 celica and caldin all have different part numbers for the lower 3sgte cover.Does anyone know the differences? The top covers are all the same numbers. I've put a gen 3 sump and pump on my gen2 so i dont really know ..
3
2013/08/21 18:53:18
dwyer125

What is this diff?

I have a late model double synchro e153 with lsd. From all the research I've done on the net it's difficult for me to say if this is the standard diff or not. I remember reading once that if looking in there is a small hole it is TRD but there was no pics.So I have these 2 pics of both sides of my d..
4
2013/08/21 13:12:47
Cayn V6SW20

V6 SW20 gearbox choices.

Hey Guys! I've recently purchased a project car that is need of a new gearbox. The car is a 1991 model Japanese import that has been converted from a 3sge to a 1MZ-fe. The gearbox had blown a couple months ago and is beyond the point of repair. I'm ineterested in upgrading to a turbo spec gearbox t..
5
2013/08/07 22:23:59

<< ..43 44 45 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account