Engines / Exhausts / Gearboxes / Differentials

To Bottom

Engines / Exhausts / Gearboxes / Differentials (p.17)
Post New Thread
Regular
Brady G

1990 SW20 3S-GTE engine mount/stabiliser - RH side top

Hi all! I'm now the proud owner of an MR2, however I've run into a few complications.. haha Does anyone have an image of this engine mount (see image)? It's near the top on the right hand side near the timing belt case.. It has worn away the rubber and is just 'sliding around' causing the engi..
3
2016/05/11 16:01:04
Gomez

Engine rebuild n/a

Would anyone on here recommend someone that's good with the 3sge engine. I'm located in Melbourne. I've had a look and i can only find shops in nsw :( Thanks...
5
2016/05/07 13:16:12
Danti

rattle noise from engine bay watch video. FOUND THE PROBLEM TO HELP OTHERS. NOW FIXED

https://vimeo.com/152047832 Is it from the heat shield. Also it sounds it's coming from the manifold I think. Anyone has similar problem. The noise was from the timing belt area. so i got Toyota timing belt kit and new water pump while i'm there.the old belt was Gate and pretty bad condition don't ..
11
2016/05/04 14:40:31
Reddtarga

Quaife LSD for an S54

According to previous posts the Quaife QDF-21E LSD for the ZZW30 should also fit the SW20 S54 trans diff. I note that the ZZW30 and S54 speedo drive gears have different part numbers.So just wondering if the S54 gear, will fit and work ok with that Quaife unit? Can anyone confirm?..
1
2016/04/26 11:52:05
Phiz

Turbo

Would a gtx3076r fit on a low mount manifold? Sw20..
2
2016/04/17 16:27:43
syeap94

Gear linkage dust boot cover

Hi All, Searched around the web for info on replacing the gear linkage dust boot cover (not sure if correct term) but could not find anything. I found the dust boot cover easily enough from amayama but was struggling with replacing it. I don't have an actual picture of it at the moment but those tha..
6
2016/04/12 11:53:57
Hoonsy

Gen3 3S-GE O2 Sensor Stuff

Hey guys, Where abouts is the oxygen sensor located on a Gen. 3S-GE? Posted some pics while I searched for it on my Showroom thread but couldn't seem to find it..
8
2016/04/02 14:46:17
Nik_Lee

3SG Beams info

Hi Guys, I have a quick question for the Beams gurus out there. Does anyone know if a gen3 3SGE inlet manifold will or can be bolted to a red or grey top Beams head? I would just like to know before I go ahead and purchase a gen3 inlet manifold. CheersNikayla..
8
2016/04/01 22:09:45
dkmr23q

Toyota mr2 gearbox oil and engine oil sump

Hi I've got a auto 1990 import Toyota mr2, and yesterday I put to much engine oil in it and it started smoking. So today I tried to drain out the engine oil and made a bad mistake and drained out the gearbox oil. So can anyone help me out on where I have to put the gearbox oil into the car? And wher..
9
2016/03/25 16:44:40
Steve_A

What gearbox would you use if $$ didn't matter?

Just thought I'd put this question out there to start a conversation, it's not something I plan on doing and I wouldn't have the money even if I wanted to! I've been educating myself on all the after market transaxles out there and was amazed how many options there are. I started looking into Albins..
4
2016/03/20 17:37:09

<< ..16 17 18 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account