HELP - URGENT!!!!!

To Bottom

HELP - URGENT!!!!! (p.68)
Post New Thread
Regular
lovemyMR2

Need assistance with exhaust system

Hi Guy, I am in need of a new exhaust system that is high flow and quiet. By quiet I mean it has to be less than 90DB when measured from 5m away at 5000rpm. Currently I have a full 3" stainless steel turbo back system which directly bolts on to the cat. As soon as I get the new system I'll be sellin..
3
2012/08/18 09:41:36
Cruiser97_80

Gen 2 3sgte to gen 3 wiring

I'm in the process of doing my gen 3 turbo swap into my '91 jdm sw20 turbo. There are a couple of wires i'm not sure about in the 8 pin fuse box connector. Pin 6 (blue wire) needs to go to pin 1 Where does the blk/red wire go which is already in this location? Where does the blk/red wire need to..
1
2012/08/17 21:42:44
bigh

Radiator Top tap leak (O ring).

Hey Guys, I changed the coolant in my car recently, and now have the top air bleed valve leaking coolant all over the darn place. it's definitely leaking out the front radiator coolant air bleed valve (the one on the top next on the passenger side). Being a 21 year old car I'm fairly sure that the o..
5
2012/08/13 17:10:36
dyl30

1990 3GSE High Idle

Hey all, my sdub is idling rather high then it should.. while cold its up around 1500 - 1600rpm and after about 40 minutes of driving it only drops down to about 1200rpm.. The idle screw is all the way out. anyone got any ideas what would cause the high idle.. its not erratic, it holds a steady i..
3
2012/08/12 12:47:11
ken.fos

3S-GE Motor

Has any body fitted a 3S GE motor to a 1987 MR2 AW11??? and will a gear box from a 4AGZE fit on ???..
6
2012/08/12 01:10:34
lovemyMR2

Need stock MR2 GT 1992 Blow off valve to get Roadworthy certificate

Hi Guys I am new to the forum, I have also just purchased an MR2, I got really lucky and found a rare hard top turbo one on carsales.com with 150000km for $8800. The thing is I have to get a road worthy certificate so i can transfer it back into my name. It currently has a custom turbo exhaust, tw..
13
2012/08/10 20:23:28
Dudeman

air con compressor removal - any bright ideas? sorted out, now all cool.

My hardtop is on a hoist at the aircon shop. Compressor is kaput, mech thinks the only way to get it out is to drop the engine. Anyone done this job and can make any helpful suggestions? Please?..
14
2012/08/09 00:42:37
dyl30

1990 sw20 coolant bottle replacement

Does someone recommend a easy way to replace the darn coolant bottle.. from looking at what i gotta get passed to get it in it looks like a mega hassle... so before i start pulling stuff apart thought i would ask you guys if you have an easy way of putting it in. cheers..
5
2012/08/05 19:11:30
LeBandit33

Aw11 went KLUNK!!!!!!

Hey guys, went to reverse out my driveway this morning and as I released the clutch the car crept back for less than a meter, then KLUNK....... Felt as if I ran something over, but nothing there. I've dodged up an accelerator cable because it had frayed but when I checked it, it looked ok! Was still..
10
2012/08/01 17:05:23
Admin

SW20 clutch master cylinder wanted urgently in Sydney

My clutch master cylinder has been sitting around dry for a few months and I tried to bleed it today and I wasn't able to get much fluid to go through. The pedal kept going to the floor. I assume that the piston has seized in the bore and the spring can't push it back. I'm going to take it out tom..
3
2012/07/31 20:39:23

<< ..67 68 69 .. - Powered by APG vNext Trial

© 2026 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account