******** FOR SALE ********

To Bottom

******** FOR SALE ******** (p.20)
Post New Thread
Regular
MG_MR2

SW20 shocks/suspension

Hi everyone, I'm considering selling the current suspension setup in my car to go to A/M coilovers. It's from a 90 MR2 Turbo, new shocks, inspected the strut tops recently and re-greased. Currently has Tein s-tech springs which are low and firm but not jarring (with my 16 inch wheels a..
1
2018/06/21 14:29:16
LindsayAW11

SW20 Dash Mats

Brand new from the USA. $75 including postage...
13
2018/06/12 19:20:34
MG_MR2

[SYD] SW20 (updated) parts for sale - exhaust, alternator, springs etc

Hi, I've gotta clear some parts from my garage so will post a list and add more/photos as I get time. Parts are for sw20 turbo: - manual transmission shift cables (good condition) - handbrake equalizer part (the part where the handbrake cable connects to then the two cables going toward..
12
2018/05/29 14:17:53
banner

Toyota 3SGTE 1991 SW20 or Celica Cylinders and rods

Selling some old stuff. on ebay at the moment https://www.ebay.com.au/itm/Toyota-3SGTE-1991-Cylinders-Rods-MR2-Celica-Group-A/153006997300?hash=item239fed7f34:g:OOAAAOSwVL5a6kv~ Pickup Rosanna Victoria...
1
2018/05/03 12:58:54
Mrskylighter

AW11 Roof racks / Bike carrier $10 in QLD!

Just saw this on Gumtree and thought an AW11 owner in QLD might be interested. AW11 roof racks / Bike carrier for $10! https://www.gumtree.com.a...-toyota-mr2/1180101355..

2018/05/01 01:57:50
Admin

GEN2 3SGTE Manifold for sale - located in Sydney

$80I can freight it if required. PM me with your post code for a price...
1
2018/04/28 16:50:14
Admin

GEN2 3SGTE heat shield for sale in Sydney

$20I can post this to anywhere in Australia at your cost. The condition is good. All it needs is some sanding and a cost of high temperature paint.PM me for a postage price...
1
2018/04/28 16:49:55
Admin

CT26 dump pipe for sale in Sydney

I'll be totally honest here. This isn't a great dump pipe. I have had continual problems with it cracking, though that could be because it was on a race car.It could be OK on a street car.... maybe.There is a crack in it now that needs welding, though it is minor.I hate throwing things out, so I'm g..
1
2018/04/28 16:33:50
Admin

Used PWR water to air intercooler

PWR barrel intercooler 10" x 6".One of the runners had a leak many years ago and was sealed. You can see it in the photo.Otherwise good.This is no longer needed as I have changed to a bigger unit.$150I'm in Sydney though can send it anywhere in Australia. PM me for a price...
3
2018/04/28 16:18:52
robk

For Sale: Forged 3S bottom end parts

Hey guys,Now that I'm upgrading to a 5S bottom end, I need to sell some of my 3S stuff. I have the following parts to sell (there's only ~20,000km on these parts since the original rebuild):- Gen 2 3S-GTE block (cylinders bored to 86.5mm, like any typical 3S rebuild)- Used CP forged pistons for 3S-G..
14
2018/04/27 13:19:37

<< ..19 20 21 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account