Go back to home

Aw11 Wrecking. Updated 11-12-12 (Wollongong, NSW) + Spare parts (4AGE+GZE)

Page: 12345.. > >> Showing page 1 of 7 - Powered by APG vNext Trial
Author
Bezerk27
MR2 Enthusiast
  • Total Posts : 43
  • Scores: 1
  • Reward points: 111
  • Joined: 2012/11/17 15:00:58
  • Status: offline
2012/11/17 15:28:28 (permalink)
0

Aw11 Wrecking. Updated 11-12-12 (Wollongong, NSW) + Spare parts (4AGE+GZE)

***Updated 7:00pm 11-12-12***
Guys this thread is very image intensive. Please be patient.
I will be updating this thread constantly over the coming week or 2. so check back often.
More parts listed as replys to thread, so please read all pages. 
MAKE ME AN OFFER Girls and Boys.
 
Many parts under negotiation - Get in FAST.!!! 
Parts, Parts and More Parts..... lots more to come.....  if there is anything in particular you need just ask...
.

Master Cylinder 1 of 2

.
 

Boot Lid. (grey stuff is only dust)

.
Cpillar Trim. Looks good on the outside. Some mounting nuts missing on the inside. See Pics below. could be fixed.

Bolts held in with epoxy. 1 missing.

.
 
.

.

Cpillar vents

Rear number plate lights

.


Cooling Fan Relay

Exhaust Mounts.

Cam Gears and Caps. (Kept in order in a piece of styrofoam) All there, just 1 side more spread out than the other. need cleaning.

 
Under Car Plastic Stone protectors

 
Front Grille (Little overspray on it. will clean up fine.)

4AGE Injectors.

Fuel rail and pipework.

window washer bottle and pump. (I will clean the greasy finger marks off prior to shipping :)  )
 


 

 

 

 

Stock Sandwich plate (goes to oil cooler)

Supercharged version LHS tail light. i have 2 complete. and 1 complete AUS delivered model.

4AGE Pistons and rods. very little carbon.

4AGZE Pistons only.

 
******MORE TO COME*******

More parts from my shed... 4AGZE ECU (Looks a little shabby but it ran my engine fine)

set of Head light Shrouds

Also i have a (No photo's yet.)
4AGE Crank.
4AGZE Cams
Supercharged Cam Covers
Stock Oil Cooler (Needs a Clean)
4AGZE Sump and oil pickup
PLUS AN ENTIRE CAR(WRECKING) & WHATS LISTED BELOW..!!!!!!!!
 
 
See Photo's at bottom of post.
Well guys, the sad story of an unfinnished project as usual. brought as a Supercharged(Aus delivered model with sc conversion) and drove it for years untill the head gasket went so i decided to turbo it and thats the end of the story. Thousands spent, Never finnished. complete 88 AW11 MR2. i have decided to part her out.
All parts are currently up for grabs. Photo's are available of anything on request
post a reply or PM me and i will get back to you ASAP. only rust i can find is on the bonnet. horizontal cracking in the rear spoiler other than that everything is straight. 
im not sure if i want to part with the engine just yet(probably complete if i do, not as parts) Any reasonable offers will be accepted. i can post pretty much anything at the buyers expense. i also have a Log style cast turbo manifold(Does not fit in MR2 but fits 4age) i also have multiples of some things eg bumpers and dizzy's.
 
Here is Half of my SPARE parts list.. i have taken photo's of them all if you want it PM'ed to you. please quote number listed on the part as i have the photo's numbered.
1 SOLD
2 4AGE Injectors (Green)
3 4AGE Fuel rail with hoses still attached.
4 Starter motor (AE92 i believe)
5 4AGZE Oil Filter mount
6 4AGE Stock oil filter sandwich plate Setup (Goes to your oil cooler. i have 1 of these also)
7 SOLD
8 Thermostat housing Small port 4AGE (Only half, other half connected to my motor for sale)
9 Water Temp sensor housing
10 Stock Fuel hose with banjos either end. (Shaped metal and rubber)
11 Water pipe (slightly pitted. painted silver. Goes from water pump to back of block)
12 4AGE upper engine dust cover with seal
13 4AGZE Full intake manifold system including Throttle body
14 SOLD
15 SOLD
16 SOLD
17 Lower engine plastic cover (With timing marks)
18 Top dust plate between engine and gearbox
19 Distributor (With cap, rotor and Heat shield - Larger sized lead version)
20 Another random water pipe (Has water temp sensor + housing attached)
21 set of 5 Original Tear Drop wheels from S/C model. (All have gutter rash around the edge. been told its all fixable by a rim repairer)
22 Original spark plug dust cover from a 4AGE (Still has plastic lead clips attached.)
23 Water pump Pulley
24 SOLD
25 Distributor (With Cap, Rotor, heat shield and Fairly new set of leads, thinner lead version)
26 SOLD
27 Master Cylinder. (Looks to be in very good nick. Never used by me.)
28 4AGZE alternaor bracket. (Exhaust side i believe)
29 Bonnet Latch x 2 
30 Air flow meter 4AGZE with mounting brackets and rubbers
31 Air flow meter 4AGZE no Mounting brackets
32 LHS Rear View mirror, electric, Black.
33 SOLD
34 Centre Consol
35 4 x 4AGE pistons and rods with caps. (Good Cond)
36 Lower dust plate between engine and gearbox
37 4 x 4AGZE Dished pistons. and Pins. (No rods. they are in my engine)
38 Every removable body panel from an 88 AW11 
39 4 x Lenso wheels. (Pictured on car) 
 
 
Thats about half of what i have, lots more to come. PM me if you need something Specific.
In about 2 weeks if it aint sold it will all be going on ebay (And i dont really want it to leave the country cause these babys are getting rare.)
 
Drop me a PM or reply here if your interested..  
  



 


 
*** Sold - Pending Payment. ***
Sunroof and Interior Cover
Short Shift Kit and knob
Under Bonnet Plastics and Spare wheel support bar.
 
post edited by Bezerk27 - 2012/12/11 18:39:19
#1


94 Replies Related Threads

    Mrskylighter
    MR2 Deity
    • Total Posts : 2156
    • Scores: 174
    • Reward points: 6592
    • Joined: 2011/04/07 19:51:15
    • Location: NSW Australia, Hills District
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. 2012/11/17 15:45:05 (permalink)
    0
    PM sent
    #2
    dnegative
    MR2 Enthusiast
    • Total Posts : 61
    • Scores: 0
    • Reward points: 1533
    • Joined: 2011/04/07 19:51:15
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. 2012/11/18 00:03:50 (permalink)
    0
    Details on the motor?
    Might be interested in buying it whole........
    #3

    Bezerk27
    MR2 Enthusiast
    • Total Posts : 43
    • Scores: 1
    • Reward points: 111
    • Joined: 2012/11/17 15:00:58
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. 2012/11/18 06:33:11 (permalink)
    +1 (1)
    hey, i need to find the bill from the reconditioners to be accurate but here is what i remember.
    small port 7 rib block (With the squirters)
    arias forged pistons, low compression (Dished i believe) with gappless rings
    polished and balanced crank from a 4agze
    i cant remember if its a small or big port head, but its fully rebuilt with o'size exhaust valves 2 angle grind. small port cams.
    4age intake.
    4agze injectors
    i believe its a c52 gearbox, i have 2 flywheels, 1 from a 4agze bigport and 1 from a 4age small port, cant remember which i have installed
    custom heavy duty Exeedy clutch.
    Sc CV's
    rebuilt by Martins engine Reconditioners in Wollongong nsw.
     
    i will dig out the bill today and check the rest
    throw a few more questions my way mate and i will try to answer them.
    it has a bit of surface rust on the block and metal dust covers from the weather, but has always been sealed up (Plugs in it, Stainless exhaust mani with a T25 hanging off it. inlets on ect. so no water inside it.)
    Regards
     
     
     
    #4
    Bezerk27
    MR2 Enthusiast
    • Total Posts : 43
    • Scores: 1
    • Reward points: 111
    • Joined: 2012/11/17 15:00:58
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/18 15:15:02 (permalink)
    0
    Parts are starting to move. Get in fast guys. im selling everything AW11 i own.
    #5
    LeBandit33
    MR2 Enthusiast
    • Total Posts : 21
    • Scores: 0
    • Reward points: 289
    • Joined: 2012/07/29 23:10:11
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/18 16:08:29 (permalink)
    0
    Pm'd
    #6

    Bezerk27
    MR2 Enthusiast
    • Total Posts : 43
    • Scores: 1
    • Reward points: 111
    • Joined: 2012/11/17 15:00:58
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/18 20:30:15 (permalink)
    0
    Also found a Flywheel this afternoon... i believe its from a 4age..


    #7
    Domma_aw11
    MR2 Aficionado
    • Total Posts : 573
    • Scores: 10
    • Reward points: 3515
    • Joined: 2011/04/07 19:51:15
    • Location: Gold coas qld Australia
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 13:49:50 (permalink)
    0
    PM sent
    #8
    dennis the menace
    QLD Moderator
    • Total Posts : 745
    • Scores: 45
    • Reward points: 3905
    • Joined: 2011/04/07 19:51:15
    • Location: Toowoomba Queensland Australia
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 15:55:41 (permalink)
    0
    Price on complete interior? - And I'm happy to strip it all out myself . . .

    Past-President, MR2 Owners Club Qld
    "There is a fine line between hobby and obsession."
    #9
    Bezerk27
    MR2 Enthusiast
    • Total Posts : 43
    • Scores: 1
    • Reward points: 111
    • Joined: 2012/11/17 15:00:58
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 16:46:13 (permalink)
    0
    dennis, i may have a buyer for the centre consol at this stage as i have sent pictures to them (Waiting on reply), but everything else in the interior is still up for grabs. lots of people asking about small items of the interior though no one has commited. im not nominating prices at this stage, taking any Reasonable offers.
     
    regards 
    Edit- Guy doesnt want centre consol, so i still have a complete interior at this stage. would prefer to pull it out myself mate as it is located at my parents house and i have too many commitments to be hanging round there for hours waiting. Sorry.
    post edited by Bezerk27 - 2012/11/19 19:18:55
    #10
    Knightrous
    MR2 Deity
    • Total Posts : 2045
    • Scores: 272
    • Reward points: 5721
    • Joined: 2011/04/07 19:51:15
    • Location: .
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 16:48:26 (permalink)
    0
    What size are the Lenzo wheels?
    #11
    Bezerk27
    MR2 Enthusiast
    • Total Posts : 43
    • Scores: 1
    • Reward points: 111
    • Joined: 2012/11/17 15:00:58
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 17:22:42 (permalink)
    0
    hey mate, Markings say 16x7JJ ET38 6.5kg
    Regards
    Edit: although it may be obvious. 4x100mm sapcing
    #12
    Knightrous
    MR2 Deity
    • Total Posts : 2045
    • Scores: 272
    • Reward points: 5721
    • Joined: 2011/04/07 19:51:15
    • Location: .
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 17:28:17 (permalink)
    0
    Ah shame they were not 15X7" :(
    Would have been very keen on them!
    #13
    Bezerk27
    MR2 Enthusiast
    • Total Posts : 43
    • Scores: 1
    • Reward points: 111
    • Joined: 2012/11/17 15:00:58
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 17:35:16 (permalink)
    0
    yeah, biggest i could fit under those small guards without rubbing anywhere
    #14
    dnegative
    MR2 Enthusiast
    • Total Posts : 61
    • Scores: 0
    • Reward points: 1533
    • Joined: 2011/04/07 19:51:15
    • Status: offline
    Re:88 Aw11 parting out. Every Part available. (Located Wollongong NSW) + Spare parts (Lots 2012/11/19 19:33:12 (permalink)
    0
    Ballpark figure on what you want for the engine? Might know someone interested.......
    #15
    Page: 12345.. > >> Showing page 1 of 7 - Powered by APG vNext Trial
    Jump to:
    © 2025 APG vNext Trial Version 5.5